Click Here

 

In this article in the next paragraph yow will discover a lot of outstanding details all about Installing A Bathtub.

Mounting a bathtub isn't exactly brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily easily accessible, the task can relocate rapidly; if you need to open up a wall surface to eliminate the old bathtub and also position the new bath tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the job as well as fit attempting it. As opposed to hiring a service provider to take control of a halfway-completed job, it is better to think about utilizing one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This write-up will aid you install a brand-new tub in your bathroom if you have actually currently gotten a new bathtub as well as don't require to transform the arrangement of your previous water supply pipelines.
Your devices and also product checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Preparing for the Installation

Firstly, the supporting structure provided with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the flexible tap ports to the bottom of both faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its final placement.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be quite bothersome because of the restricted gain access to that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Setting up the Bath tub

Utilizing the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the tub up until the level reviews level.
To install faucets, fit the bottom of the furthest flexible faucet port to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the water and also examine all joints as well as new pipework for leaks and also tighten them if required. Load the bathtub and likewise examine the overflow outlet and also the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling and sealing around the tub should wait until the tub has actually been made use of at least once as this will certainly resolve it into its final placement.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers are in location between the tap as well as the sink. Safeguard the tap in position with the producer given backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the location where the bath meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, resulting in difficulties with wetness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also installations. They are marketed in tubes and cartridges, and also are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can split fairly very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the marketplace. It is suggested to fit the floor tiles using waterproof or water resistant adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I'm certainly very focused on Tools You Need to Install a New Bathtub and I'm hoping you liked our entry. For those who liked our blog entry please make sure you remember to pass it around. I thank you for reading our article about How to Install a Bathtub.

Instant fix? Dial!